Still "Waiting for time" after reboot

[mackowiakp]

After several months I try to install very new FLASH version rev6153 of Neutrino on my AV7000 clone satbox.
The important problem I noticed is that after reboot (hard or soft) TV program is not display at all and "Waiting for time" info is display. But when I turn satbox to standby mode and to active mode again, programs are reproduced properly.
Is any workaround for this issue?

[BPanther]

Switching to an other program does not help?
Do you save the EPG? If yes, deleting the data maybe helps.
Or if connected to internet, use a ntp server instead the dvb time.

[mackowiakp]

Switching to another program does not help.
I briefly describe what I done:
- flash_eraseall, flashcp
- run Neutrino from flash, where was not any initial action for the first run
- reboot
- I set both tuners to "Independent" and to work only with Hotbird sat
- "scan the sky" was done
- reboot
- I deleted from satbox menu all bouquets related to Astra
- reboot
- set receiver to FTA channel broadcasted by my sat provider (no EMU!)
- reboot
- set CINCH output to YUM (I use composite connection because of unresolved problem of freezing picture after turn off/on TV set when connected over HDMI)
- turn off satbox, disconnect HDMI then boot again

- "Waiting for time" is display

No other setup action was taken, except uncomment in /etc/fstab entry related to /dev/sda1 to have HDD mounted in /hdd dir.

Switching to standby and resume back, resolve the problem each time I reboot satbox, does not matter hard or soft reboot. "Waiting for time" is still display for 2-3 sec but the program is properly reproduced.
But, from time to time, after reboot, satbox starts properly. Very rare, but it is possible.

After receiving Your post I set NTP to ntp.icm.edu.pl (most fast response NTP server in my country). No changes. Still "Waiting for time".

[BPanther]

No other setup action was taken, except uncomment in /etc/fstab entry related to /dev/sda1 to have HDD mounted in /hdd dir.

If the Label RECORD, the mount works automatically. Also you can use the features menu to force a mount. But fstab is also good.

After receiving Your post I set NTP to ntp.icm.edu.pl (most fast response NTP server in my country). No changes. Still "Waiting for time".

Strange, that you have such problems, because if the ntp really works, the time MUST be set right. The network check is ok in ALL points?

[mackowiakp]

Yes, network is working properly. For test purposes, I run NTP manually to see what happens. After 2-3 seconds internal clock was sync with NTP server. So I think that "Waiting for time" is result of something else than time sync. I have to mentions once more that from time to time (very rare) satbox starts properly after reboot.

[Friedel]

sorry, keine Lust auf Englisch. Das Problem mit AV7000 besteht so lange ich die Box habe. So lange hatte ich das auch beschrieben und so lange passiert nichts. Bei mir ist es IMMER so, dass die Box nach Aufspielen neuer Soft erst rebootet. Dann kommt es zu den von Dir beschriebenen Fehlern (Kanal zur Zeit nicht verfügbar und waiting for time) Als ob bei reboot der Speicher nicht vollständig gelöscht wird. Zu meinen (vergangenen) Scart Zeiten war es dann noch zusätzlich so, dass dann nach reboot gar kein Bild war (also auch keine GUI). In diesen Fällen muß ich die Box mit shutdown erst in den Deep Standby schicken und neu Starten. Ich kann es auch nicht mehr lesen, dass das nicht nachvollziehbar ist und habe die Box nun versandbereit zum Verkauf.
Vielleicht denkt man bei diesem Boxtyp mal darüber nach, den Speicher auch bei reboot komplett zu löschen.

Ausserdem wäre, wenn es nur bei einigen Boxen auftritt mal eine Übersicht über Hardware revs zu bekommen. Meine Box jedenfalls stammt noch aus der ersten Serie:
rev: 1.0

Ein weiterer Verdacht von mir ist, dass NTP gar nicht arbeitet. Bei mir ist bei fehlendem Antennenkabel auch nach beschriebener Prozedur (nach reboot Box in shutdown schicken und wieder starten) keine Uhrzeit in Infobar.

[mackowiakp]

Yep. You are right. But at this time, Octagon/AV7000 is only de facto recorder for me. My TV set has Sat receiver build-in so the only i want is to have reliable recorder with EMU facility. As simple as possible. Because of features I described in previous posts, Neutrino is not reliable recorder at this time.
So lets a look for another few months.... To be continued... I think....